| Code | Meaning | Cause |
|---|---|---|
| F.49 | eBUS fault | Short circuit on eBUS, eBUS overload or two power supplies with different polarities on the eBUS |
| F.52 | Mass flow sensor connection fault | Mass flow sensor not connected/disconnected, plug not connected or incorrectly connected |
| F.53 | Mass flow sensor fault | Mass flow sensor faulty, filter below venturi filter cap wet or blocked, gas flow pressure too low |
| F.54 | Gas pressure fault (in combination with F.28/F.29) | No or too little gas supply pressure, gas valve closed |
| F.56 | Fault: Mass flow sensor regulation | Gas valve defective, cable harness to gas valve defective |
| F.57 | Fault during comfort safety mode | Ignition electrode highly corroded |
| F.61 | Fault: Gas valve regulation | – Short circuit/short to earth in cable harness for the gas valve- Gas valve defective (coils shorted to earth)- Electronics defective |
| F.62 | Fault: Gas valve switch-off delay | – Delayed shutdown of gas valve- Delayed extinguishing of flame signal- Gas valve leaking- Electronics defective |
| F.63 | EEPROM error | Electronics defective |
| F.64 | Electronics/NTC fault | Supply or return NTC short circuited, electronics defective |
| F.65 | Electronic temperature fault | Electronics overheating due to external influences, electronics defective |
| F.67 | Electronics/flame fault | Implausible flame signal, electronics defective |
| F.68 | Unstable flame signal fault | Air in gas, gas flow pressure too low, wrong air ratio, condensate route blocked, wrong gas restrictor, ionisation flow interruption (cables, elec- trodes), flue gas recirculation, condensate route |
| F.70 | Invalid device specific number (DSN) | Spare part case: Display and PCB replaced at same time and DSN not set, wrong or missing output range coding resistor |
| F.71 | Flow NTC fault | Flow temperature sensor signalling constant value:- Flow temperature sensor incorrectly positioned at supply pipe.- Flow temperature sensor defective. |
| F.72 | Flow/return NTC fault | Flow/return NTC temperature difference too great -> flow and/or return temperature sensor defective |
| F.73 | Water pressure sensor signal in the wrong range(too low) | Interruption/short circuit of water pressure sensor, interruption/short cir- cuit to GND in supply line to water pressure sensor or water pressure sen- sor defective |
| F.74 | Water pressure sensor signal outside correct range(too high) | Cable to water pressure sensor has short-circuited at 5 V/24 Vor internal fault in water pressure sensor |
| F.75 | Fault, no pressure change detection when start- ing pump | Water pressure sensor and/or pump defective, air in heating installation, too low water pressure in boiler; check adjustable bypass, connect external expansion vessel to return |
| F.76 | Overheating protection on primary heat exchanger has responded | Cable or cable connections for safety fuse in primary heat exchanger or primary heat exchanger defective |
| F.77 | Flue non-return flap/condensate pump fault | No response from flue non-return flap or condensate pump defective |
| F.78 | Interruption to DHW outlet sensor at external controller | UK link box is connected, but hot water NTC not bridged |
| F.83 | Flow and/or return temperature sensor tempera- ture change fault | When the burner starts, the temperature change registered at flow and/or return temperature sensor is non-existent or too small.- Not enough water in the boiler- Flow and/return temperature sensor not in correct position at pipe. |
| F.84 | Fault: Flow/return temperature sensor tempera- ture difference implausible | Flow and return temperature sensors returning implausible values.- Flow and return temperature sensors have been inverted.- Flow and return temperature sensors have not been correctly fitted. |
| F.85 | Fault: Flow and return temperature sensors incor- rectly fitted | Flow and/or return temperature sensorshave been fitted to the same pipe/wrong pipe. |
| F.92 | Coding resistor fault | The coding resistor on the PCB does not match the entered gas familyCheck the resistor, repeat the gas family check and enter the correct gas family. |
| F.93 | Gas group fault | Combustion quality outside the permitted range: Wrong gas restrictor, recirculation, wrong gas group, internal pressure measuring point in ven- turi blocked (do not use lubricant on O-ring in venturi.). Gas family check prematurely terminated. |
| Commu- nication fault | No communication with the PCB | Communication fault between display and PCB in the electronics box |
Vaillant Ecotec Boiler Error Codes
Vaillant Ecotec Boiler Error Codes